Jump to content

jfasano88

Members
  • Posts

    59
  • Joined

  • Last visited

Required Information

  • FirstName
    John
  • Make
    Monaco
  • Model
    Camelot 42 KFQ
  • Year
    2009
  • City & State
    Somewhere, ALABAMA

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

jfasano88's Achievements

  1. I have found the two wires from the toe kick and put the multimeter on ohms and got nothing no continuity no beep. Then I removed one wire and turn on my breaker and it kept running. I did it again and no continuity and also was getting erotic numbers but no beep. I also sprayed the hose input with WD-40. I did it to the inlet hose and I got the same results. It might be the relay.
  2. I will try that solution. When you say toe kick is it the lever you push with your foot when you are sweeping or is it the connection you push the vacuum into the female end to vacuum
  3. No Tom I did unscrew the toe kick but didn’t see any wires. Then I did the same to the plug in and found the two wires, couldn’t unscrew the wires (to tight to the wall but I did try a multi meter but no readings. Then I banged on the the relay. I will use the WD-40. Is it ok to use the breaker when I need to vacuum. Should I bang on the relay again to unstick it
  4. I will try it tomorrow Very little room to get to it. Only enough wire for wall plate. Can’t get a screwdriver in there. I can cut the wire at the vacuum and can splice it back?
  5. I did what you said and it is working. But now it won’t turn off. I use the breaker to turn it on and off any ideas John F 2009 Camelot kfq
  6. My vacuum cleaner was working great. When I went to use it again it will not start. I changed bag and still no power. I have electricity to the unit. Checked with multimeter (has power. Is there a reset button or a fuse to change. I believe there is a 12 volt that connects to the ring that turns it on. John F 2009 Camelot kfq
  7. Hi Tom yes I called morning star they talked me thru a fix. I unhooked the power to the batteries and solar panel and took a small piece of wire and spliced the temperature RTS together and now it works. The 90/10 is 90% house batteries and 10% to classy batteries. The other setting is 50/50 % 50 to house and 50% chassie batteries. Morning star recremends 90/10.
  8. MODERATOR EDIT This new topic was merged with a similar and ongoing topic, started by same OP END OF EDIT I have a 65 watt solar panel. Does it do anything like charge batteries 100%. If I turn off my charging system is the solar doing any good. 65 watt is very low I think. I would be nice to know if it is charging my batteries. I have it programmed for 90/10 John F 2009 Camelot kfq
  9. Yes I have the original solar panel. No power coming from solar panel don’t know where my fuse is if I have one??
  10. Never ending problems. Our campground was working on the electrical systems. The power was on and off, they were checking the grid, so the power was on and off. My morning star remote meter RM-1 is flashing red every second. I am not getting any power from my solar panel. All my batteries are fully charged. I unhooked the rj-11 from both ends and still nothing. Is there a fuse for the solar panel. Need help to solve problem. Called morning star and no help there. Under my bay is the controller nothing lit up at all. I believe that the controller also has a green light when solar energy is present. Need help John F 2009 Monaco Camelot kfq
  11. Just inquiring about my aqua hot diesel burner. I don’t use my diesel burner because my electric is sufficient. Do I need to use it to exercise the diesel burner. If I don’t need to use it, is it ok not to fire it up, should I exercise it John 2009 Camelot kfq
  12. Hi again. Found my problem. I bought a very expensive water filter and the holes are so small, it restricted my water flow. Now I have military water pressure which is a high water pressure. Thanks
  13. Hi everyone I have problem with both my water pump and fresh water lines. My fresh water pressure is very low. I will turn on a facet and for 1sec I have good flow then I have very low pressure. What is puzzling is the same thing happens when I use my water pump. I turn off the the fresh water line. I believe I have something that is causing this problem with both systems. Has this ever happened to others. John F 2009 Monaco Camelot kfq
×
×
  • Create New...