Ron Shantos

Here are a few sources. http://www.dieselequipment.com http://rometruckparts.com/ http://www.amequipment.com/ https://www.wiperparts.com https://midwestbusparts.com/index.php?main_page

Just have to ask... If a mechanical issue with a rear slide, what is the concern since it has a CCM electrical system? i have a 2008 Beaver Contessa which has the Kongsburg System. Ron

Check AM Equipment. They made all the wiper components for my Beaver Contessa and I believe ALSO did for Monaco? https://www.amequipment.com/product-category/product-type/windshield-wiper-arms/ Ron

JUST ADDITIONAL INFO: Just today also replaced the 18:1 gear in a 2008 Beaver Contessa. The new ALL METAL GEAR was also purchased from Amazon. Lippert P/N 117292 bedroom ABOVE FLOOR SLIDE. NOTE: If the slide is "IN" it is necessary to cut a access hole in the bottom of the slide floor! ALSO NOTE that if the motor should fail there is NO Way to get a drill with 5/8" socket on the gear box to move the slide IN or OUT without a 36" long extension. Poor design to say the least! Just information that might be helpful. Ron

Look here: https://rveliteparts.com/products/rev-rv-10115170-louvered-dash-vent-4-hole?utm_source=google&utm_medium=shopping&utm_campaign=mid-performers&gad_source=1&gclid=CjwKCAjwnOipBhBQEiwACyGLuvsmJbmLHzFWmthMXXxbI52Hk8brtYdQ5GGR3zi6pbM5oZ1mNinFZxoCb10QAvD_BwE

Hightly recommend. FLITZ polish till clear, then a couple coats of good wax.

Just bought a Air Filter for a 2008 Contessa from: atyourplacerepair.com Warrenton,Mo 63383 636/887-6799. Ask for Todd They have CURRENT stock of most any filter. Most importantly the products have recent manufactured dates! There prices are also good. Ship UPS. Just my recent experience and will buy there in the future. Ron

Try Northwest RV. They have a good supply of Beaver/Monaco parts. https://www.nwrvsupply.com/?s=beaver+boost+gauge&post_type=product&type_aws=true

Turned on diesel on the AH DIESEL SW on control panel. Could hear a relay/or contactor on the control board "CLICKED" but NO display or control lights at all on the control board. HOWEVER, AH fires, heats coolant, and produces heat in BOTH ZONES (both zone pumps work normally). As a sanity check felt the exhaust pipe and it was HOT. Unit appears to be totally functional yet NO STATUS LIGHTS on the CONTROL BOARD. ALSO, checked the FRB for a fuse and could NOT find any fuse or reference to the AH. Thoughts or suggestions.

BOSCH RELAY for FRB? Tom is the the correct Bosch Relay you recommend? https://www.summitracing.com/parts/bch-0332209150?seid=srese3&gclid=EAIaIQobChMIt4ePqKr4_QIVjd7nAx1qtgUmEAEYASABEgIU1vD_BwE#overview

Brian, below is a picture of the endcap and where the tabs are located to remove it. Hope this helps. Ron

Try Northwest RV Supply. They used to have a supply not shown on the site. Try:https://www.nwrvsupply.com/?s=monaco+decal&post_type=product&type_aws=true

A machine shop can weld and shape that piece.

Martin, I MISSED that you used the existing trim piece! Sorry. Ron

Martin, Reference the one that was posted originally it was a 2 piece holder. See this reference file:///Users/ronaldshantos/Downloads/185857775_Newcupholder%20(10).pdf. The one at the link provided is a one (1) piece and says "La Palma - Monaco RV Cup Holder - Gas Engine Only". It appears to not have the separate trim piece covering the screws. Sorry for the confusion.

https://www.ebay.com/itm/144687088187?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=144687088187&targetid=1645685073288&device=c&mktype=&googleloc=9026836&poi=&campaignid=16730423415&mkgroupid=135815925780&rlsatarget=pla-1645685073288&abcId=9300841&merchantid=6296724&gclid=Cj0KCQjwjvaYBhDlARIsAO8PkE39nrpFuZTPgut34CfQe7Mb4bLF3_lSphep-n-vEk6XKH7KU8EtEgsaAj3JEALw_wcB

Martin, Thanks for the response. Really interested to replace the POS cup holders in our 2008 Beaver Contessa. The originals are not useable. Await your response. Thanks again, Ron

Where can I get the SLT file? Thanks, Ron

Problem resolved. The switch in the electrical bay was defective on the retract side. The switch is a Carling SPDT. Found that they can be carefully taken apart and clean the contacts. The contact were not pitted but just dirty. Put it back together and all works. I did order a new switch on ebay for a backup. Thanks for all the GREAT info! Interesting that this circuit does NOT have a relay providing the voltage to the hydraulic pump instead of a switch for the open & close. Ron

No, I only have 1 switch in the electrical bay below the driver. Thanks for your response

The hydraulic system (pump) also operates both of the FRONT room slides in & out with NO problems every time.. The slide EXTENDS the generator with NO problems. The problem is RETRACTING the generator slide. I suspect the generator slide switch in the lower driver side bay OR the relay. I have NOT been able to locate the generator slide relay, I assume that it is relay controlled. Pushing the retract switch repetitively will eventually retract the generator slide. I do not know the model. The hydraulic pump is Lippert

MODERATOR ACTION This is the original Post, with the title edited to include pertinent information. A DUPLICATE was just posted.... This is in violation of the Site Rules. No action will be taken at this point.... Please DO NOT REPEAT or DUPLICATE A POST... Generator slides hesitates to CLOSE when the switched is pushed. Will eventually close after repeated attempts. ALWAYS OPENS on the first attempt. Suspect the rocker switch or the relay?? Any information on where the relay to CLOSE the Generator Slide is appreciated. Ron

Joe, I have a 2008 Beaver which should be close. I have A SCS system. Model number is by the dryer assembly. Acme Air Parts has most parts. 913/515-1560 ask for Richard. Richard@soldbyrichard.com. They should have your parts. Ron

They are in a 2008 Contessa. Bet yours do also. Ron

If all else fails call Rev Group, 877-466-6226. Give them your VIN # and they should be able to provide one. Ron