Mike Farquharson

HI the measurements are are mm but this is what I had machined. My wheels are hub pioleted so that measurement

needs to be real close.

spacer.pdf

HI every one , h frame was ok tires were inflated to 100 PSI motor home was empty , ended up having spacers machined to .250 and used 2 of the plastic spacers that go between the wheels to center the wheels because the axle was welded 1/8 inch to one side. Went with 1/4 inch spacers because the lug nuts would not let me go any wider . It seams to have fixed it as it does not rub.  Thanks 

Yes Pictures would be helpfull. Thanks

HI  thank you all for the great ideas will be going to motor home this weekend to work on it , timas996 thanks for the picture of of the drawing it helped me find the correct 1997 drawing found on the down loads page that frank suggested. pacbrake sent  me a drawing and a tuturial as how the system works.

Thank You Mike Farquharson

HI 1998 monaco dynasty cummins 8.3 C does not appear to be working am looking for a wiring drawing so I can trouble shoot It .

Looked at the drawings in the down load pages but found nothing.  Thanks

thank you

Thank You Tom Cherry

Thanks for the replys, removed passangers side wheels, in side wheel same as drivers side and part number.

drivers side hub face to bolt 11 3/4" passangers side is 11 7/8" 1/16" out, the bolt on passanger side showes some rubbing  and tire showes some markings but no damage , tires look new am wondering if the toyo tires have a larger cross section.

Thanks Mike

Thank you for your ideas, wheels are accuride # 28408 offser 6.6" part # says 8.25 width date code on weels 07/97 tire sizing matches what posted in motorhome , h frame welds look good,tryed to move axle hub with a 6' bar and no movement, measured hub face to bolt head at 11 3/4"  and wheel face to tire and got 11 7/16 not enough room ?

I will pull passanger tire off tomarrow if I can find a jack stand

I ment 11 13/16 

HI I was hoping find a solution to this problem.

1998 dynasty 34' wheels are factory as are the tires 295/75/22.5 , axle is welded to H frame I bought it 1 1/2 years ago did not notice the rubbing have ben remodeling it only put 300 miles on it sence I got it.  picture is of drivers side passanger side shows very lite marks but has not groved it. tires at 90 psi it lookes like i could put 1/4" spacers as the lugs are long enough , Any ideas .

Thanks Mike

Hi I am having the same proublem can you tell me the supplier for the spacers and lug studes.

Thanks Mike

looking to source part numbers and suppliers for the tierode ends and drag link 1998 monaco dynasty 34'

thanks

Mike Farquharson

Thank you all for the info should help me greatly

Hi am looking for a incoming power drawing have looked in downloads lots of stuff after the breaker panel , have no 120 power nothing tripped at the inverter or in the breaker box , have power going in to transfer switch. 

Thanks Mike

Hi I just removed the kool matic , have thermostat fan grill and inside cover cover has some cracks but all work.

Live near spokane WA

Thank You

Thanks everyone , steve could you still fit the inner panel even though you did not use it ?

Goodmorning I am needing to replace my neoangle skylight my dimentions are 34x16x5 tall Icon sells one with thoes dimentions but only 4" tall do you think this would work.

Thanks Mike

Hi did your coach come with a monostat sattelite dish ?

Thanks Jim

Thank you Jim so their should be a check valve on the pump to stop back feeding and you open the valve to fill the tank while preasure still goes to the pump at the same time. On the passengers side of the tank at the top it looks like a vent their is a hose with a garden hose adapter on it . I guess to fill it also.

The fitting on the pass side left I am guessing it is also a check valve.

Thanks Mike

Hi I am trying to redo the plunbing in the wet bay the water fill uses a gate valve and preasure would be on the water pump all the time , I am use to a fifth wheel that uses a 3 way valve for the incoming water.

Thanks Mike

Thanks it is a1998 dynasty has a momentary 3 position rocker switch.

Thank You

ordered pump switch rtl30a18v for the water pump it lookes like the replacement switch it is on-off-on but need a momentary-off-momentary does ant one have the correct part number or a scorce for this switch.

Thanks Mike