bigbhb
-
Posts
33 -
Joined
-
Last visited
Content Type
Forums
Downloads
Articles
Gallery
Blogs
Events
Store
Posts posted by bigbhb
-
-
-
I ordered a new lock and key from Veurinks rv center,$95us.
-
No the door opens and closes great,The latch is working fine. It won't lock or unlock.
-
8 minutes ago, Dr4Film said:
Did the key work properly before?
The key has to move the tumblers inside before the key is allowed to be turned in either the lock or unlock direction.
Explain exactly what you have determined other then "my key will not lock or unlock the door the door from outside."
More specific explanation is needed before more troubleshooting can be supplied.
Yes the key did lock and unlock the door prior to this. Sounds like something has moved inside where the tumblers are so the key does not align with the tumblers.Manually from inside you can move the lock latch.(not talking about dead bolt)
-
-
Myron, watch that bigbhb guy! Lol
-
-
Thank you to everyone. Unfortunately the awning that I have does not have adjustment on it.
Thank you
Brian
-
Need to adjust ohd awning.The fabric goes out to far, causing arm to extend to far and lock,then cannot retract awning
Can't find manual to get end cap off,don't want to break it. serial # is on rail behind cap.
not sure if this model has adjustment on it,others when you extend them you can see the 2 adjustment arrows.
2006 monaco holiday rambler.
any help would help thank you
-
I would like 15 Land 15 R
del pueblo rv resort 14794 s avenue 3 e site 281
sounds like a great idea for the grandson. WIN WIN.
403 863 1927 BHB0@TELUS.NET
Brian Barker
-
Used Chris in Yuma he is very thorough and knowledgeable and does a very good job and stands by his work.
- 1
-
How does one get in line? totally interested
16 driver side
14 pass side
thank you
-
-
-
Just to inform all.
went back out and found bolt connecting slide motor to left end of slide fell off found bolt but not the nut so I put another bolt and nut but sheered both ends off have to get a nut for the first bolt.
I can not believe the torque on the slide motor!!
with the right bolt and nut will work fine.
-
Hello again.
I had rot on bottom of slide. So I ordered and installed guardian plates.
tryed the slide a few times and it worked fine (in and out 1/4 way with plastic on)
did not take the plastic cover off the plate before riveting and glueing.Mistake!
so to take all the plastic off completely I pulled the slide in about 4" to lift the slide up to pull the plastic off from inside the moter home the side closest to driverseat went good did same to other end got all the plastic off now the slide seams to be only pulling from one end any ideas what it might be?
If you are inside the moter home looking at slide the left side closest to fridge that end gets pushed side ways to the fridge wall and the other end is coming in.
any hep would be appreciated thank you.
-
Good point eclipse
-
My 20ft carefree awning quit working.Have power to motor but cant get at it because awning is against motorhome wall.how do you open awning with no power to check if motor is shot?without breaking motor cover and can not get to hook alternate 12v power to it
-
Looking for the ground for the Aladdin.the pic comes and goes for the camera and is jumping with lines.That is why I think it is the ground.Any help at all would be appreciated.Sometimes it works fine.
thank you.
2006 holiday rambler endeavor. -
All working fine now. Need to check batt for any bad plates.
-
Just want to say thank you again to the group!!
To know there are people out there that want to help their fellow man.
Brian.
-
reset the magnum and all is working .
thank you for the help
Brian
-
No fault on generator.Happening with nothing on just takes a little longer.
thanks for input any help is appreciated!
-
Table top for 2006 Holiday Rambler.
in In Search Of…
Posted · Edited by bigbhb
add size
looking to replace my old one,mine in the picture has been repaired.
44x28