gburgman2000
-
Posts
45 -
Joined
-
Last visited
Content Type
Forums
Downloads
Articles
Gallery
Blogs
Events
Store
Posts posted by gburgman2000
-
-
-
your work is amazing..
- 1
-
-
Just a link to my last upgrade.
https://www.irv2.com/forums/f115/2004-dynasty-airdog-raptor-install-532793.html
- 1
-
When we run we always turn on our headlights then we never get the alarm as there is enough drawn to offset the over current alarm.
-
-
I agree, there will be no service after the sale from here on out.
-
Did the Mirror bases match the coach curve or did you have to finesse them to the body?
-
I will not as I replaced it about 4 years ago.
I will be using a time delay relay to turn on the raptor after the main lift pump shuts off to avoid an over pressure situation thou.
-
as a side note they have the curbside and roadside swapped.... I know for a fact that the AH/Gen pickups are on the PS/curbside as well as the sender so I suspect the Engine is as well
I will know soon enough as I am adding a raptor pump above the tank
-
-
One end is at the water pump, the other end should be out of the back side of the head. At least on the ISL...
-
https://www.irv2.com/forums/f115/my-thoughts-on-the-nason-parking-brake-switch-197560-3.html
Bob details how to build your own in a PDF in post #32
-
I just replaced all of my valves, one was leaking so I am sure they others were soon to follow.
Reused the long actuator bar that was on the original as the new ones were to short.
-
I will when we see him this winter.
-
Jack winters in FL with us at Camp Florida resort, he has many stories of the early days with his signature.
-
yes after look at where it is blocking or 20 ton jack stands under the rear frae rails will have to do
- 1
-
it may be safer to dig a pit below the where the radiator goes than to depend on the air bags..
I have a heavy set of ramps 2x12's and plywood that I put mine up on for all things under the coach so even if air drops I am still safe
- 1
-
All back together and working fine.
Total materials to change out the boiler and all hoses.
9 gallons of Century Boiler concentrate 9 gallons of distilled water (ordered 5 gallon pails direct form Century, much cheaper).
70 feet of 5/8 Green stripe heater hose
10 feet of 1/2 Green stripe heater hose
1 foot 3/4 Green stripe heater hose
2 dozen big cable ties and 100's of paper towels and 1 tyvek suit.
The engine side.
New water pump from Cummins M&D distributors Part#: 5579024. Old one was not leaking but soon would have. $181.94 Much beefier than the original, better flow do to revised impeller.
7 gallons of antifreeze 7 gallons of distilled water
Thermostat was new last year so did not change.
Many hours of fun under the back end to do the hoses.
The front was very simple roll the generator out and the hoses were right there along the center about 10 foot each
- 2
-
AH.. yes I missed that, all brass is better. Replacing all of mine as one is just starting to act up so time to do them all
-
-
ok, thats what mine looks like. Thanks
-
Richard, how did your fan shroud attach to that new rad, my dynasty has the same one or close an I thought the fan shroud was bolted to it? may have to go look
-
To soon to tell 🙂
Aqua Hot rebuild
in AC, Heating, and Cooling
Posted
Take lots of pictures and i used tape labels as well.
It's really not that bad and there should be plenty of slack but it may be zip tied in a bundle above the unit.