Rob Monda
Members-
Posts
32 -
Joined
-
Last visited
Content Type
Forums
Downloads
Articles
Gallery
Blogs
Events
Store
Everything posted by Rob Monda
-
2006 Dynasty Aquahot will not FIRE. Suggestions? Help?
Rob Monda replied to Rob Monda's topic in AC, Heating, and Cooling
I just sent them a request. That would be great if you could My cell is 9177099266 if you want to text and I could give you an address -
2006 Dynasty Aquahot will not FIRE. Suggestions? Help?
Rob Monda replied to Rob Monda's topic in AC, Heating, and Cooling
Great thanks -
2006 Dynasty Aquahot will not FIRE. Suggestions? Help?
Rob Monda replied to Rob Monda's topic in AC, Heating, and Cooling
Thanks for the reply. Other than shutting the switch off in the coach is there another way to reset? -
2006 Dynasty Aquahot will not FIRE. Suggestions? Help?
Rob Monda replied to Rob Monda's topic in AC, Heating, and Cooling
Does anyone know where the fuse is on an Aquahot AHE 100-04s. I found a 15A in the main fuse paneL under driver seat. Still can not get to fire. I have changed the Nozel and filter. I am getting a perfect spray and plenty of pressure. I checked the spacing on the electrodes. I ran power to the electrodes and had plenty of spark. I am not getting power to the ignitor thru the brown and yellow wire. Is there something that I am missing? Any advice would be greatly appreciated -
Just finished re-installing microwave. I changed the start capacitor and it started right up. Pretty easy getting back in I put the unit on a milk crate on top of the counter and was able the angle the back up in to bracket then lift the front and screw in the mounting screws.The part cost me $54 including shipping from repair clinic. On to the next problem. Thanks for all the help
-
Thinking of updating Tail lights
Rob Monda replied to 8thDegree's topic in General Motorhome Discussion
With LEDs it is harder to see the difference in brightness during the day. I found the same thing when I upgraded headlights and fog lights to LED. The LED head lights and fog lights are a lot brighter at night. I know there is a noticeable difference with the tail lights at night. I had gotten a blowout and was stuck on an interstate in Connecticut for 12 hours and decided I needed brighter tail lights after watching all the road warriors blasting by at 90+ for several hours -
Thinking of updating Tail lights
Rob Monda replied to 8thDegree's topic in General Motorhome Discussion
The white section of my back up lights were there as they are on Ford vans. The lights on my bumper light up with the landing light switch on the dashboard. The back up lights are in the tail lights as they were from the factory and work. The hookup was basically you use the original harness. The back up lights were reused and just mount in the new tail lights. The tail light harness plugs in to one of the existing bulb sockets. They are a lot sharper,brighter and work with no hyper flash. I am very happy with them -
Thinking of updating Tail lights
Rob Monda replied to 8thDegree's topic in General Motorhome Discussion
I had this issue with mine on my 06. Mine had 2 sets of Ford E series van taillights. I searched and upgraded to IPCW LEDs . I found them on Ebay. After searching different brands I bought the IPCW on Ebay for about $275 a set. I was looking at others on a Google search that were about double the price. I had to do a little modification but they are basically plug and play. You end up using the original back up bulb but the tail lights are LED. I am very happy with them and the look great. I also have no issues with Hyper Flashing which is something That I was concerned about. If you zoom in on this pic you can see them -
OK so yesterday I removed it with no difficulty. It had the two screws under the grease filters as Dr4film had said and there were two square head screws attaching microwave to cabinets. It came right out. After watching some youtube out came the multi meter and I checked the start cap which I believe is shorted. I ordered yesterday and we will see if that corrects the issue. The unit itself is pretty clean so I figured I would try to fix. I am seeing replacement cost up around $600. I did have a problem with my rear AC blowing fuses and that also turned out to be a power cap. Pretty easy to change just have to be careful with high voltage. Part should be here tomorrow and I will keep you posted. Thanks
-
After reviewing some of the info you guys passed along I took a good look at it this morning. I tried two fuses powered it up and turned on with the carousel off. The machine made a growling sound and then blew the internal fuse again. It was manufactured in 2004 so I think it is time to change. It looks like there are two screws where the grease filters are. I do not see any screws going thru the top of the unit. I am going to try and remove today. Thanks for all of the input
-
My Sharp carousel microwave keeps blowing the internal fuse. I am thinking of changing the unit because it is the original and approximately 18 years old at this point. Does anyone know if the upper wood trim panel pop off like some of the other trim panels in the kitchen. I figured I would ask before taking apart. Any advice would be greatly appreciated
-
2006 Dynasty Aquahot will not FIRE. Suggestions? Help?
Rob Monda replied to Rob Monda's topic in AC, Heating, and Cooling
I have no water in my fresh tank will it fire if there is no water in the system? -
2006 Dynasty Aquahot will not FIRE. Suggestions? Help?
Rob Monda replied to Rob Monda's topic in AC, Heating, and Cooling
OK I will check Thanks -
So I was having some recent trouble with my Aqua Hot. I was working fine most of the winter then I started smelling raw diesel dripping from the tailpipe. I changed my R filter and changed the nozzle. I have a nice spray mist coming out when I tested but it still wont ignite. I also checked the electrodes for proper placement and found them to be perfect. Is there any way to check the coil? I checked for 12 volt with the pump running at the coil and had no power. The wires I tested are the two coming out of the pump that attach to the coil. Any Advice would be greatly appreciated. Thanks
-
I am having the same problem with mine at this point. I realized it when I had it on and smell raw diesel dripping from the tail pipe. Also No heat was coming from the exhaust. Just ordered new filter Gar Ber R and a new nozzle. Waiting for them to arrive but I believe the service will solve the issue. I haven't serviced in 2 years.
-
Looking to upgrade side view cameras
Rob Monda replied to Rob Monda's topic in Audio, Video, & Electronics
I contacted Paul Whittle regarding my cameras. He had what I needed and I was able to replace on the rig without removing the mirrors. The hardest part of the job was replacing the screws and getting the old hardware to work smoothly. Other than that cameras work great. Thanks again Paul It was great speaking with you -
Air still not coming up on 06 Camelot 40 PDQ
Rob Monda replied to BRBowers's topic in Compressed Air Systems
Sounds good thanks -
Air still not coming up on 06 Camelot 40 PDQ
Rob Monda replied to BRBowers's topic in Compressed Air Systems
Where do you find the dump valve? I have an 06 Dynasty -
ISL 400 OIL DIPSTICK
Rob Monda replied to Rob Monda's topic in Engine, Transmission, Engine Cooling, & Hydraulics
Thanks for the info. I opened up the floor in the bedroom and saw the dipstick. I just need to get a plug for the fill Thanks all -
Would anyone know the correct part number for an Transmission Oil Dipstick for my 06 Dynasty with the ISL 400. Just took a look and mine is missing
-
Rear camera monitor in Bedroom
Rob Monda replied to Rob Monda's topic in Audio, Video, & Electronics
More good advice. Thanks I will check later today -
Rear camera monitor in Bedroom
Rob Monda replied to Rob Monda's topic in Audio, Video, & Electronics
Great thanks for the advice I will check it out -
Rear camera monitor in Bedroom
Rob Monda replied to Rob Monda's topic in Audio, Video, & Electronics
It powers up it just doesn't get any picture. its just a gray screen -
Does anyone have any experience with the video monitor mounted next to the bed. Mine just shows a gray screen. I believe it is a 7 pin connector and they are hard to find these days