Kent Madison

I cannot find the door bell chime location on my 2009 Holiday Rambler Bismarck 4 to see why the door bell doesn't work. I did find this box on the wall going into the rear bath. I don't know what it does as it's batteries where dead. Changed the batteries and still nothing.

The men at RV Cams had what I needed. Great service. Voyager RCA/Power adapter: https://www.rvcams.com/p/31300006.html RCA-to-Sony adapter: https://www.rvcams.com/p/VCB-AV12.html Thanks for all the help.

Thanks. I now know how to fix it if it acts up again.

Thanks

Thanks. It's on my Monday list.

I have looked for some to no avail. Thanks

I replaced my aftermarket Sony camera with the original Ramco factory mirrors and cameras. I now need to wire them up to the aftermarket Sony video box. Can anyone help with the process. I have a Voyager monitor. The original ASA plug is 4 pin and the Sony is 6 pin. Both have a red, white, black and shielded wire and the Sony also has a green wire. I was hoping I could just splice the two wires together. Thanks

Thanks

I might try that if I need more cooling. Thanks

it ended up being this temperature switch. Tapped on it and it started cycling like it should. Thanks everyone for the help.

Thanks

PCB in the FRB???? Not sure that this means. Sorry

The fan blows but the AC clutch will not engage and the condenser fan will not run.

On my 09 holiday rambler navigator Bismark 4 the dash AC works some times and not some times. I had the same problem with the wipers so I installed the 5V fix and that corrected the wiper problem. I am wondering if the Dash AC is also ran through the front CCM and if the low voltage that front CCM is providing could be part of the problem. I have checked all the fuses and they are good and I put in a new AC condenser fan a few months ago. Getting ready to travel south for a few weeks and would really like the AC working. Any suggestion on if I need to add the 5Volt fix to the front AC CCM wires like I did for the wipers? Thanks

I would take a dozen for each side if you decide to make them.

I took one of the LED out and put the old filament bulb in that spot and it stopped the rest of the LED from being dim. Make me think that the CCM is sending low voltage into the light to tell the computer if the lights are burnt out or not. The LED tail lights of my two trailer are also on dim. Does anyone know if there is low voltage always running through the lights?

That would be great, as I would like to defrost without the overhead fans if I don't need them. Thanks I will have to figure out a work around.

On my unit I can run the top fan on the two different setting in any position of the heater/AC switch except for defrost. On defrost it overrides the rocker switch and I can not control it at all. Is yours the same?

That is where I found mine also. I took it out and cleaned it up and re-oiled it and it is better but still quite load. I wrapped the squirrel cages in foam and did not screw it back in place as the motor noise traveled into the wood and made it loader. I don't like the way that it comes on high only when the defrost is turned on even if you don't need it. There are lots of times that you do not need the extra air movement but still need the defrost. There is a 2 speed switch on the side panel that runs that fan, but you cannot slow the fan to medium when the defrost is on. Has anyone just by passed the defrost control part and just let the rocker switch be the power source? Here are a few pictures.

Sounds like a Sunday project to me. I will see what I find. Thanks

Ok thanks. I still only have the 3.5 volts going to the smart wheel. I have the 5 volt power converter ordered so I will still put it in even tho the wipers started working again.

After replacing the two solenoids that run the tag axle lift dump valves and stopping the error message on the Valid leveling system the wipers started working again. Could the bad solenoid coils have been putting to much load on the CCM and causing the wipers to not work?

Thanks. I will look into that area.

Well. I had unusual day today. I was having problem with the valid air ride system and also with my wipers. I discovered the two solenoids that dump the tag axel where bad. After changing them the wipers work again. Is the air rise system ran through the front ccm where the smart wheel runs through?

I have a 09 holiday rambler navigator whose bay lights and porch lights are also always on. They turn on with full brightness when I switch them on but stay on dim when they the switch is off. I had replaced then all with LED lights bulbs and I just assumed that there is some very low voltage leaking by that is enough to keep the LED light lit. Has anyone else had this problem after installing LED?