gdroberson
-
Posts
112 -
Joined
-
Last visited
Content Type
Forums
Downloads
Articles
Gallery
Blogs
Events
Store
Posts posted by gdroberson
-
-
that not the problem I have replaced the bags and shocks and been over every thing with a fine tooth comb I think it was the way it was built the book is for a 32 f00t mh mine is a 30
-
my mh rear bags are a inch lower than what the book says but if I hold the right height rod and try to raise it it will only go up about a 1/4 inch and is maxed out so I just left it alone
-
on mine it turns the jake break on and off
-
should be the break button /switch
-
I fixed two doors and three corners of my MH that was damaged when I got it used the paint from auto zone probably used 8 cans and you will not see where I repaired it unless I point it out to you the canes are not that big and cost about 11.00 a can
-
Auto Zone dupli.color duplicates original chrysler colors BCC0401 champagne pearl
- 1
-
amazon NS1-79750LW round indicator light
-
I replaced mine it has power but still does not work have to check out ground side have not done that yet
-
on the track arm that is just dust covers that have goon bad I have been trying to find replacements no luck so for and cant find new replacement ends
-
that is where I got mine from fit right in the place of the old one just could not use the camera cover on the back
-
it is raised letters right right above the arm in your pic but looks to be a sheppard 80 if it has 3 bolts holding it on I think the 100 has 4 bolts
-
get what you pay for probably could get it at Hd or lowes amazon just google the part no nothing special about it just a 120 volt element
-
element probably has a pen hole in it they make a noise when it is shorting out when the hole gets big enough it will kick the breaker
-
M80 has no replacement only the 100 just had my M80 rebuilt only have drove it with a 30mph wend but seamed to be much tighter than before
-
-
-
OK finished getting it in and seems to be much tighter have a 30mph wind so it blowing me around had it done at ARE Automotive rebuilders express Glendale ph. 623-842-9628
-
OK the new tie rod end that I found at straight line suspension PN 462.ES8426R thomas tie rod end different rubber boot was told they dont make the original one any moor
-
I just had my m80 rebuilt they dont have a replacement for the m80 only the m100 and it should be a tas65 66003 pitman arm is 84263202 but double check with Weller I just had my m80 rebuilt yesterday in the process of installing it now
-
I have they dont have a build sheet for my rv
-
tried the no. at spicer no match
-
it has a tag it says monaco coach corp. 080400-0004 02828300 model f4w-0800 google it got nothing
-
no NAPA or big truck repair close will check when I take the steering box to Glendale to be rebuilt Monday thanks
-
posted this in another forums no answer try this one I have a 2001 holiday rambler dp 30' and where the tie rod end that is attached to the steering box had a thick rubber grommet raped around a big washer in between the tie rod end and the steering arm now it is gone need a replacement either grommet or a new tie rod end no part no on the old one the only thing I found was a d230 stamped on the back and a rt4on the end of the shaft where the castle nut screws on any help would be appreciated I have it off wright now taking the shepherd m 80 to be rebuilt next week thanks
ironman tire load
in Tires & Wheels
Posted
OK on our way to Redding ca from bullhead city first trip in this new to us MH 01 holiday Rambler 30'have 6 new ironman 255/70r 22.5 load rang h tires trying to find the chart that will give me the pressure to set the tires at had I weighed at the first scale we got to and the weight is 6660 on front ax. and 14740 on the back 21400 total can I use any chart or does it have to be Ironman cant seam to find a chart for them and how do I do the rear divide by 4 or what any help will be appreciated Thanks Gary