JeffM31

Installed a new map/boost sensor. Driving it Sunday and I’ll let you guys know if the problem is gone or not.

Well, upon further inspection I spotted a spot about 9 inches long on the inside above the drivers seat where the seal was not in place around the bend. Got it back in place and the light is gone. I still ordered some urethane for where the two rubbers meet though. Thank you everyone.

Thank you, I was thinking about using proflex

Hi everyone, What sealant was this? The sealant between the 2 rubbers. The seal looks good but I can see light in one spot from the inside out. Don’t know if the windshield was ever replaced or not but the one corner sucks. As usual much appreciated for the help.

Thank you

I need to get a Scan Gauge Nope small normal puffs here and there.

Yes it’s super slow.

No I haven't. Yep no check engine or anything on

100%

Awesome. That’s what I’m definitely leaning towards. I think I’ll just do it. Thank you

I’ve just been watching Aladdin and the gauge. I’m leaning towards the map/boost sensor

Hello everyone, I have a weird issue that may be no issue at all. My 400 ISL has zero power until it hits 35mph then bammmm. The odd part is after you turn it off and back on a time or two the power is back. I got it to operating temp just to be sure it wasn’t a built in safety but it still did the same thing. All filters are brand new and yes it did the same with the old filters. One other thing I noticed was Aladdin read like 6 psi and the dash gauge was around 28. Thoughts?

I didn’t notice much honestly maybe a tad. It was just city streets. In the long run it should give me a tiny increase in fuel and definitely help to lower the egt’s.

So I had no other choice. Hopefully this help someone. I went overkill with the 8" model. Used a rotozip to cut the hole. I used this one. Thank you everyone for the replies https://www.amazon.com/dp/B07ST8XDQD?psc=1&ref=ppx_yo2ov_dt_b_product_details

Just drove it to get tires, it sounds great. Love the increased turbo whistle too

Hahaha maybe the same person installed both of ours. Super crappy design. I’ll see it the el I ordered works, if no a 10” will be the solution

I ordered this short el so hopefully it works. I was curious if Monaco had some weird adapter for it.

I have an 06 Dip that is new to me. Outside today, I was in the wet bay looking things over. Is there a special elbow to use for dumping without the sanicon? The elbows I have won't mount to get through the wet bay floor. Thanks in advance

I did. I like it. It may just be preference. I may change my mind towing a grade but for now I love it.

Yes, muffler is gone. Haven't driven it yet to see any difference. The noise is there when on the throttle but honestly I don't feel its obnoxiously loud at all.

You're very welcome. Any questions feel free to reach out

I think I will put it all in the slide out tray. Thank you guys

Good morning, I have always been a fan of Leisure Led so I thought I would share the lights. The main old thin lights are what were changed here. They almost cover all of the thin light imprint. Super happy with these. They have Off, 25%, 50%, 75%, and 100%. I ordered them in natural light. These were basically plug and play. As long as they are centered up they will screw into the aluminum. The other link is the screws I used to mount them. Night and day difference. https://www.amazon.com/dp/B0BF5Z2L6N?ref=ppx_yo2ov_dt_b_product_details&th=1 https://www.amazon.com/dp/B09MDZY3Q3?psc=1&ref=ppx_yo2ov_dt_b_product_details The puck lights I ordered are these, huge difference also. Same natural light also. These are plug and play also, they fit directly in the hole. https://www.amazon.com/dp/B07WPY398C?psc=1&ref=ppx_yo2ov_dt_b_product_details All of the storage light bulbs I changed to these. They seem to be plenty bright. Same bulb for the porch light too. https://www.amazon.com/dp/B08LCZ2R7T?ref=ppx_yo2ov_dt_b_product_details&th=1 The bathroom fixtures, wall sconces, map lights and outside step light I used these bulbs. Super bright also. https://www.amazon.com/dp/B09Y5JQFP1?psc=1&ref=ppx_yo2ov_dt_b_product_details I removed the front and rear compartment pull lights and added these instead. Yes they are bright https://www.amazon.com/dp/B072BJHTGK?psc=1&ref=ppx_yo2ov_dt_b_product_details In the kitchen I ordered these. The ballast have to be removed. I haven't received them yet but the reviews are great. https://m4products.com/t8-36tube-nw-natural-white-36-f30t8-12-volt-t8-led-tube-light-4500k/ I changed out the camera monitor because I had a line in it. The new monitor was not compatible with the Aladdin so I ordered this small monitor to see Aladdin https://www.amazon.com/dp/B0746CM3G7?psc=1&ref=ppx_yo2ov_dt_b_product_details This is the new monitor I used https://www.amazon.com/dp/B083G5GGCJ?psc=1&ref=ppx_yo2ov_dt_b_product_details Along with changing out the cooling unit in my no cold this is the bright LED bulb I used for that https://www.amazon.com/dp/B07DGX84MR?psc=1&ref=ppx_yo2ov_dt_b_product_details Off topic of LED's I decided to change the U-joint. Not that bad of job with the right tools. https://www.amazon.com/dp/B0084FF710?psc=1&ref=ppx_yo2ov_dt_b_product_details My transmission wasn't reading any temp and found out its because Monaco used a 400 degree sensor. I ordered a 300 degree and all is well. The gauge will actually show about in the middle now. If you're fast you can change it without losing much fluid. https://www.amazon.com/dp/B07KJT6B5K?psc=1&ref=ppx_yo2ov_dt_b_product_details Head light switch was 100 bucks from RV places. Its a basic Chevy switch. This is it for 26 and some change https://www.amazon.com/dp/B000C9SAJC?psc=1&ref=ppx_yo2ov_dt_b_product_details Went ahead and straight piped the exhaust too. Couple hundred and done Hopefully this can be helpful to a few Jeff

Good morning. Is there any issue storing oil, tranny fluid, etc in the inverter cabinet? It just makes sense to me to have the spare stuff in the rear storage compartment. Thank you

I just bought it. I knew about it but previous toyhaulers and things were no issue to repair. This solid piece floor is getting me.