I am pretty sure you have hub piloted but you can match yours to the attached. 

You have to stay with diameter bolt that fits snug to the hole in your mounting brackets. You should also have a steel bushing inside the rubber on the shock. 

SLI31SA Duracell Ultra Flooded 950CCA BCI Group 31 Heavy Duty Battery, 

Napa and Interstate also has them.

It looks as if you have rot on the edges from the pics. You may need to add guardian plates to fix that problem. You should be able to get that piece of aluminum from a rv salvage yard if it is not a stock extrusion/shape. Talin RV in Florida may be a good source/help for you also.

There is an existing forum “Ride Height Adjustment 08 Camelot” you might want to look at it. It appears they never found it for 2008 but adjusted to 8 13/16”.  If you read in your instructions in step 6. It refers to doing the rear valves next. So it means do the front valve first. Not very plain.

Here is a copy of the Ride Heights for Monaco's.

1991 - 2008 Ride Height Chart.pdf

Read the instructions in the owners manual. I know for the Diplomat you adjust the front first. Any adjustments on the rear effect the opposite front corner.

If you are referring to the ball joint covers. P/N 90.13127 from Energy Suspension. I had a rubber cup on mind and this on fit good.

I should have said the rubber cup on mind was torn. Grease caps fit the Zirk fittings which you don’t need.

Go to the forums on here and search “Help! Stranded in Houston. Lost Drive Shaft, Coolant hose and damage to air valve(s?) Need resources and advice” . The culprit list a good tow company and RV repair shop. He was broke down on south 69 so not far from you. Maybe that shop can send a maintenance tech to your location. Hope this helps you out.

Try Home Depot it looks like they have one that would work for you.

The Houghton is a stand alone unit. You only connect the 120v AC electrical to it. It has a remote control like a TV. So I kept my old thermostat to control the furnace. I wrote an article on how to make the furnace to work. It fits the same plenum with out any modifications. It is an easy instillation. If you decide to go that way I can walk you thru it. In the air conditioning threads look at “ Houghton Install/Thermostat Dead”. It has pictures etc… how I did the install to make everything work.

Kenneth

Cut the hose and get a hose barb splice and clamps to stop it from leaking. When you get home have a new hose made and route it properly.

I replaced my front unit with the Recpro Houghton. I have ran it for 1 summer and 1 winter. It is much quieter than a penguin and the heat pump works down into the 28 degree range. Very easy to install also.

In case you do not have the Magnum Manual I have attached it for you. In troubleshooting it tells you how to reset they system. Hope this helps.

64-0002 D (Owner Manual, ME Series).pdf

Just pull or back out of building if you think you are going to hit. Then turn it all the way both directions. I did not jack my front end when I changed to the the TRW to set the poppet without any problem.

It will be the rear brakes stuck. You can hit them with a hammer and break them loose. I just recently ripped my rear end because I couldn’t find a hammer where I was parked. So I tried rocking it and boom it stripped gears in the rear end. Only about a 5,000 fix. So beat them loose.

Just measure the light and go to Amazon they have them. I bought one on Amazon several years ago and no problem so far.

I just changed the alternator on my 2007 diplomat with a 400ISL. It appeared to be a P/N 8RG2142, it had overspray on it and hard to read. AJ - Electric will know what you need. I just replaced mine with one from them and was working like it should.

I wouldn’t worry about since you have driven it several thousand miles that way. I think you are suppose to check the oil level with the tube pushed in. It pulls out to make it easier to fill. 

Not the easiest to find. I have done 2 of these. Not hard to do. Good luck, you will like it.

Monaco_door_gas_strut_upgrade.pdf

Please post the time and date for the meeting

If you do not want to go residential then try JC Refrigeration’s mod. It works well. Also known as the Amish.

https://jc-refrigeration.com/

Someone with a 3D Printer could possibly make it for you. 

You change it thru the bedroom floor. I sent you a PM with my number. Give me a call and I will explain it.

On my 2007 ISL 400 the fan is 30” and the shroud is 31”.