Romeo84

Steel exhaust flex pipe is what I used when mine fell off going down the road. But mine was gone gone. You can still fix yours.

Thanks everyone for the help. Swap was super easy Just replaced the whole assembly, and wouldn't you know it? I get back home and my wife said the keys were in her purse the whole time. I bet I have over twenty hours tearing into every door, drawer, closet, garbage can at home and in the camper looking for those bad boys. Welp Now I have a spare ignition and a whole bunch of spare keys. 🙃

So it is a fairly simple swap?

Well here is my current situation. I have just recently lost my ignition key ring. Yup all of them. Ironically I have pictures of the trimark and FRB key so I have the numbers off them but..... Does anyone have advice on how to replace the ignition 2001 signature. I believe I remember someone saying it's off an old chevy ignition.. Any helper advice would be awesome. Would would I source these keys at or am I just outta luck.

Went through this last year. The purge valve in the air dryer was old dirty and not sealing so it never fully seated. You can get a new purge valve kit for cheap it doesn't come with the slide valve though. I bought a new air dryer off Amazon that was defective so don't do that. If the needle stops building its in the dryer.

I just bought and I stalled this 6 months ago. I didn't have a direct wire. Which as Said earlier is better. I can't complain about quality or lag in video. Every now and again it may freeze for a second but otherwise it's definitely live and clear. Plus you can honestly mount them anywhere. I put one at the back of the car dolly facing forward towards straps and golf cart to watch for movement. Close to 60 feet behind drivers dash and works great.

Oh man that's exactly what I was looking for!!!!!

We have the switch and the faucet for the insta hot in our signature. Is that a dedicated run? Tom, I think you wrote out exactly what I was thinking. Thats why I haven't done it yet i don't want to run a whole new independent line. But now I'm interested to see if that insta hot run like dr. Mentioned is Independent.

This was on the list of things to do this year! So funny. The only thing we Use in our camper was the stove. I wanted to remove the tank and make a giant tool storage compartment. Saw someone at a campground last This year that did the exact same thing so I know it's possible. Like the other guy said Need to do a little research on power... in my signature I have an outlet under the sink for a subwoofer. Pretty sure it's a downstream run that could be turned independent. Curious how much a small 2 burner induction stove uses. Can't be more than a microwave?

Hey guys I had my flex pipe under the motor between the muffler and the downpipe fall off on my drive home this weekend. Seems like it's a pretty standard part but if any one has a part number that would be cool. Real reason for the post is Does anyone have a picture of their rig with a straight pipe. After hearing her roar Like that, I kind of want to put a straight pipe on It. Looking for pictures and parts they used. 2001 sig ism . Thanks in advance

With the engine running it has to be building air. See if you can listen to hear the leak if it's coming from the air dryer or the bags leaking make sure to have someone step on the throttle to build rpm. Will increase build pressure making it easier to hear. Also the governors are cheap and easy fix like posted b4. So if it's not building ez fix Try to find out if it's losing air or just not building it.

I drive truck, and I don't understand why trucks he's parked in the left lane. So frustrating. Dude probably was trying to pass him for 15 miles and the trucker was completely oblivious never checked his mirrors and notice 40 some cars stacked behind him. Then dude doesn't even pull over just stops. Probably caused a secondary crash behind him 2.

Yikes which filter. If it's the ravor plastic prefilter those are getting tricky to source. Your unit should have a electric primer at the rear. With the Key on and depressing the valve hold the button till full till fuel comes out. There pretty ez

Nice! Congrats on saving about $3000!!

Where did you find this diagram. I need these schematics lol

They are little round cones.. u can pick them up at menards home depot lowes.. I think 10 come in a bag for $5. Bring the old 1s with and just ask.

I have the exact same amount of oil. You can pull the chrome piece off and your tag hub seal will be visible. Mine had a clear window on it as attached. More than likely the center rubber grommet dried out or was pulled out and didnt seat properly. When you take the cover off youll see where its leaking. Don't over fill it. If you see it by the full line it's perfect. Also that plastic is very britle over time. If and when you replace grommet push gently or you'll push right thru the plastic. 😆 All providing its oil filled... lol

Well written! Thanks. Actually did what you said probably while you were typing it. Thanks again!

Well I think that answered that. There it is. That's why is coming out. Thank you. Did It just unscrew??

Ok so the bottom picture is the shut off to the pump. It shouldn't back fill with that closed right? Also after the pump runs water flows out of the inlet which I would expect to be the remaining water in the lines right? What stop that?

Yes the valve is moving. Wondering if I didn't have it turned or closed fully. Still don't understand the back flow out of the supply inlet when pumpbis running Well said and written! Had to be bad valve in the pump allowing water to back flow into the tank. Same thing with after the pump runs allowing water to flow out the inlet supply

Exactly but mine filled somehow.... I will try it. I'm thinking it's not sealing. And some water is leaking by.

Yours sounds more like a clog stuck check valve. I had the rubber insert clog the inlet once. Mine is filling when it shouldn't be. Feel like maybe the same check valve wherever it is went bad.

Hey guys had my city water connected and everything worked fine. Went swimming and my daughter came back and said the camper has a huge pool around it. Somehow my city water filled the fresh water tank and was pouring out the over flow. I double checked everything to make the valve was the right way. How did the fresh water tank fill? Where is the check valve that would prevent that? Also instead of dumping the water we just switched over to the water pump just to use it. But now water is coming out of the supply connection port. Any thoughts?

I did order it and it looks close I have yet to install. Mine was 10.5 as well. I was thinking of trying to just replace the nylon roller. It's just a cover but haven't got around to that yet. Keep me in the loop if you get to 1st. Wanna know what om in for lol