pwhittle

Hi Richard,

I cut the switch apart so it is just down to the pins, then desolder them one at a time. 

It helps to have a good solder/desolder station.

Paul

Good links Bruce!

I have bought replacement joysticks from Mouser before and Digikey did not have any at the time. Mouser's stock was getting low, but it looks like there has been more received, so that is good news.

They can be a bit of a chore to remove, depending on what equipment/skills you have, but fairly straightforward.

5 hours ago, Dr4Film said:

My only dash Aladdin Joy Stick is temperamental.

Richard,

I had the same symptoms and fixed mine by soldering in a new joystick.

Paul

Hi Robert,

I have a few.

I’ll Pm you my phone number.

Paul

I worked on another keypad today where the programming for one key position was not what it was supposed to be.

It is easy to fix once diagnosed, but something for us to keep in mind when troubleshooting.

Paul

Mike sent me his keypad.

I read the program off it and saved it for later.

Then I programmed in my test switch panel config and tested each switch. No Problem Found.

I reviewed the original program, and the key for Aquahot 110V was programmed to send the wrong code compared to the wiring diagrams. I have reprogrammed the switch to send the correct code to the CPU, and it is on its way back to Mike. I also prgramssed a spare switch on the panel for the same function, so Mike has a backup key if that same one loses the correct code.

I have not seen this issue before, but expect this will fix it.

Paul

23 hours ago, pwhittle said:

I rebuild them, but if Faria still does it, send it to them as they likely have a supply of bezels which I don’t.

I am traveling out of the country for most of December, so if you need it soon, PM me.

Paul

To be clear, when I repair the gauges, I remove and re-install the bezel. You can see this has happened from the rear, but not when it is installed. I 3D printed a mount to protect the bezel. I posted the print on Monacoers.org for the DIY people with access to a 3D printer.

Paul

I rebuild them, but if Faria still does it, send it to them as they likely have a supply of bezels which I don’t.

I am traveling out of the country for most of December, so if you need it soon, PM me.

Paul

Hi Dennis,

I was not suggesting buying the gateway. That was the simplest way to show people what the gateway looked like.

I sent you a PM.

Paul

On the Faria systems, the air lines terminate at the Faria Gateway. The Gateway also has other sensors/transducers as well as an interface to the J1939 bus. On our 2005 Signature, the Faria Gateway is mounted on the ceiling of the first or second bay on the Driver's side.

Faria Gateway GW0015A - Northwest RV Supply (nwrvsupply.com)

Paul

My gauges continue to operate fine after the fixes.

The time consuming part is removing the bezel and crimping it back.

Paul

This matches the top and bottom hinge.

https://www.ebay.com/itm/154214828243

DA61-03230B  Samsung Hinge OEM DA61-03230B

My bottom one broke and I 3D printed one which I installed on the top without the spring. I also ordered the one above and it is a match.

I’ll take a look at the middle hinge tomorrow

Paul

That should work.

I’ll Pm you-

Paul

You should come through the Atlanta area and stop in so we can take a look.

Paul

I was able to do that because our motorhome had one that failed.

I don’t have access to a Thetford Tecma mechanism.

Paul

H Buzz,

Do you mean the 110V outlet for the Tv that is disabled when the ignition is turned on?

Paul

I have replaced the joystick on some. I think I have some spares too.

Best is to repair yours as I have seen a couple different models (with and without beepers), but I think they are all compatible.

I even got better at printing the bezels.

Please PM me if interested.

Paul

I mounted my BMK shunt by the inverter.

Paul

Do you have another one of the same modules? You could switch them over by setting the dip switches on each module. And see if the issue follows the module.

Paul

Hi Ray,

We have found that the need for the kit is not really important, and not worth the price it would end up being for me to put together and support.

The same program was used for all coaches in the same year, and we typically have backups of a coach that will work on yours if the controller were to fail. Also the failure rate of the controller is very low.

The two I know about that failed we’re caused by water intrusion or 120v on the multiplex bus.

I don’t charge for backups or programming your equipment. I do charge for repairs (to keypads) or if I have sourced a keypad or controller and you would like to buy it.

My phone number is on my profile, or PM me. I am north of Atlanta.

Paul

Here is a 3D printable one.

paul

Marinesan.com is another supplier.

https://marinesan.com/base-seals-m-o-plug/

Paul

@Scotty Hutto just up the road is Sleepy Hollow Rebuilders. 13357 Cumming Hwy Cumming, GA 30040 (770) 887-2649.

Ira is second gen and took over after his Dad retired. He has always been very fair with me.

Paul

The mounts are an Intec part, but I believe they only sell them with their cameras.

I will take a look to see what I have here, especially as you are mounting one of my camera kits in it. 😀

Let’s talk tomorrow.

Paul