birdshill123

I need both gas struts for my 08 Dynasty. I have seen part numbers for other models but they list 150 lb. Struts. Infortunately mine have nothing printed on the strut. I did nottake measurements but the piston diameter is about the same as my cabinet struts. I can match the collapsed and extended lengths but need the "lb" rating. The mechanism is very complex with lots of mechanical advantage. Any help appreciated.

Rv service reviews sounds like a good idea but it is useless.Many of the listed shops are out of business. Most only have one or two review sand they are outdated. W aste of time Asking at a cg office is a good idea.

I was using my phone when I posted and I have big clumsy fingers. It is a J1939 protocol/ The wiring from the ECM is on the right hand frame rail near the top. Sort of above the DPF. There are a bunch of wire bundles covered with plastic loom. The grey connectors are usually covered with electrical tape. When Jason was still at Monaco he told me to look there first as they had reports of that connector being a problem. But there are others as well. In the basement ceiling the computers for the ABS and The Allison are part of that harness. I think everything is daisy chained. I think there is another connector close to the turbo. The whole system is ill designed. OTR trucks also use that protocol but the harness is very short. When truck shops have a problem sometimes they just change the harness. Cheaper that spending 2 days looking for the problem. Did you clean all the battery terminals. You want them to shine like a copper kitchen item!! There are other battery cable connectors on the walls of the battery compartment. Look inside that armrest for blue crimp connectors. They can be bad. If you go to IRV2 do a search for j1939 or no data. Others have had that problem. Have fun Hypoxia. I think the dash unit is by Medalion. A little different. Hard to find but a good electronic tech can fix them.

You may have a bad connection in theCAN communication from theECM. This is the j1g939 protocol. Monaco had some problems withthe way they ran the wiring. The 2 wires are bundked with other wiring. They use Deutsch connectors. These are small supposed to be weatherproof connectors. Grey triangular shape They run from the right rear all the way to the front. Sometimes moisture rusts the small pins . You eill find them amongst the wire bundles on the right frame rail. But I would start with cleaning all your battery terminals They should be shiney!! Then find all the ground connections . Most are onthe frame rail. Tajethem apart and brush them clean. On my Dynasty there is an ecm fuse in the rear run bay One owner found a rusty fuse holder. Be aware that if you have ashop do the work you could easily spend $5000 and the problem would still exist. On the Dynasty there are also connectirs in one of bays behind the bay ceiling. On my unit the dash wires go to the driver armrest. When your dash goes crazy the ECM may put you in limp mode.Hope this helps.

It is near impossible to get an electric fan that will cool a 400 HP engine. Do a Goggle for the amount of cfm Cummins requires. Then do a Google for the electric fans that produce the required CFM. You would need a larger alternator and room for multiple fans. You gain nothing. There is a reason why the higher end coaches have either a Hydraulic fan o a belt driven unit. Prevost has gone to an electric system but it is 24 volt and requires a cioputer and lots of room for the multiple fans.

Thanks Bob and Paul

Hi: I have searched but do not see anyway to add photos. Do I use a hosting site and insert the URL? Thanks Brucce 2008 Dynasty

Thanks for the link Gary. I will try to add a photo but on the Dynasty the big boy is mounted in the rear run bay. The bird is a board. I think it is intellitec. There are 2 other solenoids mounted next to the big boy. Lots of wires. When i have some time i will post my current (pun) problem with the house charging. It is very wierd.

Gary. Thanks. I went to his list of posts but nothing older than Jan.13 is shown? Bruce 08 Dynasty

Our 08 Dynasty has the Big Boy but the controller is a board in the rear run bay. I would love to upgrade to the Blue Sea unit. How do I accomplish this? Thanks Bruce

been driving with furnace on for almost 50 years. Never a problem.

Chris: Why is the coolant level gauge mounted at the side of the tank? I will double check later today but it would be very hard to read. Shouldn't the site glass be at a higher level? I know Bob Nodine likes to use the older style AF but I switched over to the long life coolant years ago. If one is anal about checking with strips the Old fashioned stuff is fine. If not you can destroy the liners. At one time OAT was hard to fund but now it is everywhere. Even at Wal Mart. Cost is about the same as regular diesel AF. Once and done!

Ron: Do you sell LED bulbs? Do you have a website that shows what is available? Thanks

My BIL had a 45 player in his car. I think it was mounted on some sort of gyro. You could play them while going down the road. My wife still has a cassette player!!!

The Femco unit is far superior. Not made in China. Used to be imported from Sweden and now made in Canada. It is a real machined piece. Used by many truck fleets. Not cheap but worth it. I have had one on every RV I have owned for more than 20 years.

This is great. I never liked he Yahoo format. You have done a great job.