pwhittle

This trim may work for the main awning adding tape to the edge of the round part like in my link above. https://www.trimlok.com/rubber-extrusion/epdm-seal/p-profile/2452-series Paul

I’ve had my ScanGauge D for a couple years plugged into the diagnostic port by drivers left knee, but last trip it was not working. Display was blank. I also tried plugging into the engine bay diagnostic port. Engine and transmission data is available via the Aladdin system. I called ScanGauge and described my problem. They had me send it in to have it checked out. They found no issue, but sent a different unit back, which also doesn’t work. Has anyone else had the same issue? Paul

See if this post helps. It was for the slide toppers and the window awnings on our 2005 Signature. I am not sure this seal would work for the main awning. Our main awning and the door awning have a different type of seal from Monaco, shaped like a large T. Girard recommended the same thing for the slide toppers and window awnings, but I think it would be too big. Paul

The fourth wire will be Audio from the rear camera. Paul

I used this. Southwire 19190008 6/3 & 8/1 SEOW 50 Amp, 125/250-Volt Outdoor Extension Cord CA-Style CS63 Twist-Lock, Custom Blended Jacket, Extra Hard Usage Cord, 100-Feet, 100-Foot, BlackMore information: I removed the connectors and got enough installed that I have 50ft outside the coach when it is all out of the powered Glendinning cord that drops into a container. It is much smaller diameter and more flexible than the original Glendinning cable. Glendinning has different sized drive rollers for the smaller diameter cable. It is normally priced around $300, not the current $500+ it is currently showing. Check for other sources. Paul

In our 1994 Signature it was in the front run bay, below the driver’s window. Paul

Hi Becky, I am glad the new controller fixed your problem. Paul

Thx Jim, There was a box in a top shelf on a door, and the flap was under the door seal. Removed that and will monitor some more. Paul

Back to not right today. Pulled the cover off the evaporator and it was all iced up and the drain hole had ice in it. Used a hairdryer to clear the drain hole and melt the ice. Power cycled it and waiting to see if it starts to cool. Paul

Hi Kevin, I am glad you got to take your trip! Paul

Back to normal this morning. It likely power reset when we shut off the generator. I’ll keep an eye on it.

Our RF 197 has worked great for the four years we have owned it. For the last few days the freezer has worked great at -2, but the fridge is set at 36, and the fridge is showing 53 degrees. Any suggestions on what to check? Thanks in advance for your help and suggestions Paul

Richard, The wiring diagram looks like the bay door switches are interrupting 12V from the Slide Disable Relay. Paul

What at the preferred RV Surplus locations in Elkhart? I would like to find a matching ottoman for our 2005 Signature. Paul

I am still looking for a mechanism if anyone has, or knows where one is. Thanks! Paul

The Faria gauges are driven on a Faria Canbus between all the gauges. There is a separate Faria Gateway that Canbus that gets all the signals and send a them to the gauges. Faria no longer supports these gauges as they were custom for Monaco. Paul

https://www.mikescustompaintinginc.com We have an appointment there for a full paint job on our 2005 Signature later this year. Paul

I have looked into it. The black part is a tricky shape to print, but the real challenge is the clear plastic which is what deteriorates more. That would be very difficult to 3D print and be functional. There are some 10 button panels that only have 6 buttons, plus 4 more inputs from regular switches. There is a second 6-pin connector on the back of the PCB. Perhaps yours are like that. Paul

Ram mounts just work great, and are not priced too high. Paul

Hi Jim, It was great that you were able to get some of those keypad plastics. They are specific to Monaco and not available from Intellitec any longer. You will be able to change the functions assigned to each button and add new functions to previously unused buttons. Paul

Hi Woody, Hard to say without a picture. You can text them to me at 678-772-3847. Paul

Hi Woody, I drive with the monitor and other devices like that. I do not find it obstructs my view to any noticeable degree. I try not to get that close to vehicles in front of me, and there are gaps between the screens to see immediately in front if necessary. There are various video switches/combiners available on Amazon that work well. Take a look at @Scotty Hutto’s camera update thread. On our 2005 Signature access to the rear camera is from outside. A plate screws off from the rear outside and our camera is mounted to that. If you see silicone, you likely have to slice through it to remove a plate, then clean it up and use silicone to reinstall it. Can you post some pictures of yours?

Hi Brett, I am finalizing the instructions and the tools to make removing the keypad covers easier. I want to make it as easy as possible for users. The kit will allow you to backup and restore your main CPU and your keypads. You will also be able to change which functions are on each key on the keypads, so if you have a spare key position, you can assign a function to it. Changing the programming within the CPU is not typically possible for end users, but is available from resellers. The keypads in our coaches were specific to Monaco and are no longer available. Other Intellitec PMC keypads will function, but will look different and may need you to enlarge the hole the keypad is mounted in. I am located in Woodstock, GA, a northern suburb of Atlanta. We have a trip planned to go to Chicago in late July. Paul

Hi All! I am looking for a mechanism from a Magnum Opus toilet. A member here has graciously loaned me his spare unit for the last 12 months or so and I want to return it to him in advance of his upcoming trip. I know some people,have replaced them and maybe someone has one laying around if you are like me and cannot bear to throw anything away, even if it is no longer useful. 😀 Let me know and I am happy to pay for it as well as shipping. Thanks in advance! Paul

They let us stay overnight. Arrive before the museum closes at 5PM, then they lock the gates till it opens in the morning at 9AM. They have a truck/RV pull-through parking area with about 10 spots.