veraken

I believe the switch you are looking for is a Delco D1588 which you can get from any auto parts store. https://www.autozone.com/electrical-and-lighting/headlight-switch/acdelco-headlight-switch-d1588/919149_121215_10866 https://shop.advanceautoparts.com/p/genuine-gm-parts-headlamp-switch-d1588/3965708-P?utm_medium=affiliate&c3nid=IR-10079&utm_source=ir&c3ch=Affiliate&clickid=V1nx9h3HIxyLTPo0TWXZ0S3wUkEVdtwJyxZxWk0&utm_campaign=10079&krypto=B2tc7EZPOmqqBEXY0gGfb8v9UIKpDCTmPnrOCX5tXR0Qi4VPyEopKtVLfFzFDZSdmh25ncEx%2FytCMr0txDMWQ1+OW4BmsUOarEcZwHh3RxlRMRCxG4Wq65R68yphdT2wmlJaDPrNUHIvYo3AqfPITrctftdPpcdkOx%2Fvhjzv23KTSpSObnZOsWY3Mk%2FPbCQ2BmFRKTVZfgGowUbM3t85uxUNqbye+xSBYlDGPEVyByHXudF7k777WVIQ3ph9gCHOqPZBukkASfxwLecDe8NilF5UsbgHExUCzl5a5mRfL3TVKXz%2FuuvTJvM1G6ntSx79LNy3NYMWqY6v1WOn7vPpsg%3D%3D&utm_content=89591&irgwc=1 https://www.napaonline.com/en/p/ECHHL6554?impressionRank=2

There wer several residential refrigerators that would fit my current opening with only minor mods. I decided on a Frigidaire FFTR1022QB which, once removing the doors, fit thru my door opening. (current model FFET1022UB)I did a ton of research before replacing my Norcold RV refrigerator and this one came out #1 by far. If you plan to make the conversion, here are some things to consider.1. These fridges are not built-ins and will require clearance for air circulation. The Frigidaire needs only an inch on either side, which is probably all you'll have anyway. The back only requires 2" clearance. Other brands wanted far more. Don't be tempted to skip that. They do call for 12" on top, which is impossible for a MH. Instead I installed fans (see #2 below).2. Operating temperature. Other brands I looked at said their fridge wouldn't operate below 60 or above 90 degrees, and warned against using in a garage. No such restriction on the Frigidaire. Just keep it between 10 and 110 degrees, per the manual.3. It fit my existing opening with only minor modification.Installation:1. I installed a separate 120v outlet controlled by a switch inside the MH so that I could easily turn the unit off when not needed without going outside to pull the plug (some units do not have an on/off switch).2. I chose not to seal off the existing outside openings. I put a screen on the lower opening and installed 3ea. 12v fans in the upper vent to assure good air circulation. I used the 12v wiring from the old Norcold and put the fans on a thermally controlled line with a separate switch inside my MH.3. In the back, I anchored the unit by putting 2 lag bolts through the bottom metal rails of the refrigerator into the flooring.4. Inside, I attached (using 3m 3M Scotch 4910 VHB Tape 2 sided tape) 2 metal brackets to the top of the refrigerator and then screwed these to the wood above the refrigerator. I then trimmed around the perimeter of the fridge with black plastic L channel which I purchased from Display Products online ( Extrusions by Display Products Online). This can be purchased with the tape already attached.

Look in the Downloads section. I uploaded the Firestone Aire Spring Replacement Guide which will help you decided which airbag is the correct replacement.

See if this helps. Carefree Spring Chart - Change & Tension.pdf Carefree Omega II Install & Service Manual.pdf

Just ordered the following item which looks simple and relatively inexpensive. Missing the voltmeter, but can always use a voltmeter if needed. https://www.amazon.com/dp/B088D2JVN4/?coliid=I3Q8M56ZEA2O87&colid=2SKIZ1L3ZC7J5&ref_=lv_ov_lig_dp_it&th=1

Thanks !!

I'd be interested in making the pedestal tester you made. Could you please post the parts list and instructions to make one. Thanks!

Take a look at this video

Ramps and jack stands are the best/safest way to go. This is what I bought. https://www.summitracing.com/parts/sxt-1522a

Contact Paul at AZPETE on the Irv2 forum. He works for HWH and can answer your questions. His email is pfmaddox@att.net and his phone number is 602-549-3638. He is a Commercial Member of that forum and has posted that his phone is always on, and if not answered, leave a message.He has helped others on that forum and I am sure he can help you.

Here's a good source for replacement seals https://www.steelerubber.com/camper-rv At the bottom of their web page (under Resources), there is a link to their videos which may help you.

Question. For those of you that bought from Stone Vos, did you get the vinyl or the acrylic fabric? Why?

Had the same problem this past summer when at a campground but cleared up once I got on the road. Called TST and the problem is caused by interference with others at the campground that have the new unit. Told TST that I use the system to check my pressures before I leave and having to remove each sensor to check manually is not acceptable. If your older monitor is less than 2 years old, TST will send you a new monochrome display AT NO CHARGE.

Here's a pdf that may help you. Door Bushing Replacement & Latch Adjustment.pdf

Another thing to consider is the door hinge/swing. From the picture the Samsung has the hinge at the end. Make sure there will not be any interference when you try to open the door. The Sharp has a spacer between the door and the end of the microwave to allow the door to open even if it is next to a wall.

I have the non-flow thru sensors. I removed the "theft lock" by just removing the 4 screws holding the cap. This makes it much easier to put the sensor on.

The older I get, the less I remember, but when I saw it, I thought it might come in handy someday. Glad I could help.

Here's what I have. Look at page 15-16. Hope it helps. 1998-2000 Monaco Chassis Schematic.pdf

Here's a source where you can get completed cables https://www.batterycablesusa.com/

Recently replaced my alternator. I found the best price at Quality Power. I decided to replace my 160 amp Leece Neville with a 200 amp Delco Remy 28SI. The install was fairly simple (I have a side radiator) except on the DR you don't connect the excite wire since it is self exciting. I had my old LN rebuilt and carry it as a spare. https://www.qualitypowerauto.com/category_139/RV-Alternators.htm

I replaced my 160 amp Leece Neville 2824LC with a 200 amp Delco Remy 28SI. The install was fairly simple, ( I have a side radiator) except on the DR you don't connect the excite wire since it is self exciting. I purchased mine with a extra pulley wheel at:https://www.qualitypowerauto.com/catalog.php?category=139I had my old LN rebuilt and carry it as a spare.

Ernie Ekberg is the guru when it comes to flooring. You can visit/join his facebook page and see some of his work. https://www.facebook.com/groups/221768331584448 We replaced our furniture with theatre seating we bought from Bradd & Hall. It was a good experience and are very happy. https://www.braddandhall.com/productcart/pc/home.asp

x2 Steele Rubber Products. The have some installation videos on the bottom on the page which might help you. https://www.steelerubber.com/camper-rv

If you need new seals, here's a good source https://www.steelerubber.com/rv-home-windows

In case you don't have it, here is the manual Xantrex RC-7 Manual.pdf