veraken

Ramps and jack stands are the best/safest way to go. This is what I bought. https://www.summitracing.com/parts/sxt-1522a

Contact Paul at AZPETE on the Irv2 forum. He works for HWH and can answer your questions. His email is pfmaddox@att.net and his phone number is 602-549-3638. He is a Commercial Member of that forum and has posted that his phone is always on, and if not answered, leave a message.He has helped others on that forum and I am sure he can help you.

Here's a good source for replacement seals https://www.steelerubber.com/camper-rv At the bottom of their web page (under Resources), there is a link to their videos which may help you.

Question. For those of you that bought from Stone Vos, did you get the vinyl or the acrylic fabric? Why?

Had the same problem this past summer when at a campground but cleared up once I got on the road. Called TST and the problem is caused by interference with others at the campground that have the new unit. Told TST that I use the system to check my pressures before I leave and having to remove each sensor to check manually is not acceptable. If your older monitor is less than 2 years old, TST will send you a new monochrome display AT NO CHARGE.

Here's a pdf that may help you. Door Bushing Replacement & Latch Adjustment.pdf

Another thing to consider is the door hinge/swing. From the picture the Samsung has the hinge at the end. Make sure there will not be any interference when you try to open the door. The Sharp has a spacer between the door and the end of the microwave to allow the door to open even if it is next to a wall.

I have the non-flow thru sensors. I removed the "theft lock" by just removing the 4 screws holding the cap. This makes it much easier to put the sensor on.

The older I get, the less I remember, but when I saw it, I thought it might come in handy someday. Glad I could help.

Here's what I have. Look at page 15-16. Hope it helps. 1998-2000 Monaco Chassis Schematic.pdf

Here's a source where you can get completed cables https://www.batterycablesusa.com/

Recently replaced my alternator. I found the best price at Quality Power. I decided to replace my 160 amp Leece Neville with a 200 amp Delco Remy 28SI. The install was fairly simple (I have a side radiator) except on the DR you don't connect the excite wire since it is self exciting. I had my old LN rebuilt and carry it as a spare. https://www.qualitypowerauto.com/category_139/RV-Alternators.htm

I replaced my 160 amp Leece Neville 2824LC with a 200 amp Delco Remy 28SI. The install was fairly simple, ( I have a side radiator) except on the DR you don't connect the excite wire since it is self exciting. I purchased mine with a extra pulley wheel at:https://www.qualitypowerauto.com/catalog.php?category=139I had my old LN rebuilt and carry it as a spare.

Ernie Ekberg is the guru when it comes to flooring. You can visit/join his facebook page and see some of his work. https://www.facebook.com/groups/221768331584448 We replaced our furniture with theatre seating we bought from Bradd & Hall. It was a good experience and are very happy. https://www.braddandhall.com/productcart/pc/home.asp

x2 Steele Rubber Products. The have some installation videos on the bottom on the page which might help you. https://www.steelerubber.com/camper-rv

If you need new seals, here's a good source https://www.steelerubber.com/rv-home-windows

In case you don't have it, here is the manual Xantrex RC-7 Manual.pdf

Get your ESN (engine serial number) and go to https://quickserve.cummins.com/. Register your vehicle. It's a great source for info on replacement parts. You can also call Cummins Customer Service ( 1-800-343-7357 ) and give them your ESNThis will tell you where your ESN is: https://www.dieselpartsdirect.com/finding-your-cummins-engine-serial-number

This what I purchased from HD. They periodically have it on sale for $99.https://www.homedepot.com/p/RIDGID-6-Gal-Portable-Electric-Pancake-Air-Compressor-OF60150HB/303379052I then went to HF and purchased the following which I put on a slip mount near the compressor. Cost @$60 after 20% offhttps://www.harborfreight.com/38-in-x-50-ft-retractable-hose-reel-62344.htmlAfter adding the necessary fittings, it works great. Don't have to run the motorhome to air up the tanks and when not on shore power, I just run the generator.

Here's a document from Xantrex re: acceptable GFCI to use. Someone else had a similar problem and was told to use a Hubbell GFRST20 GFCI Xantrex Witch GFCI Recepticles Work vs Inverters.pdf

Surebond is a good substitute for butyl tape since it butyl based. http://www.surebond.com/SB-140/ If you need a source for a new skylight, here are somehttps://www.eztopsworldwide.com/ https://www.icondirect.com/skylights/ http://www.foxlite.com/

We have the NC Quick Pass Here is the link that explains the NC Quick Pass, You want the NC Quick Pass E-Z Pass Interior Transponder.https://www.ncquickpass.com/resources/Pages/nc-quickpass-transponders.aspxThe NC Quick Pass E-ZPass work on toll facilities in North Carolina, Florida (SunPass), Georgia (Peach Pass) and the following states where E-ZPass is accepted.DelawareFloridaGeorgiaIllinoisIndianaKentuckyMaineMarylandMassachusettsNew HampshireNew JerseyNew YorkNorth CarolinaOhioPennsylvaniaRhode IslandVirginiaWest Virginia

Call Sharps USA Customer Service 1-800-237-4277. They may be able to help you.

If you're interested, here is a thread on IRV2 where a member is removing his CAC & radiator from a 1997 Monaco Dynasty. In his latest posts he has started to remove them and is posting videos as he progresses. https://www.irv2.com/forums/f115/1997-monaco-dynasty-cac-and-radiator-part-numbers-497497.html

Contact Paul ( AZPETE on the Irv2 forum). He works for HWH and can answer your questions. His email is pfmaddox@att.net and his phone number is 602-549-3638. He is a Commercial Member and has posted that his phone is always on, and if not answered, leave a message.